Saber Foundation Repair serving San Bernardino County, CA

Lisa L. of Green Valley Lake, California, had noticed that the floors in her home were sagging and the walls had begun to bow.  The first step she took was locating a foundation company with a great reputation, to fix her issue.  After doing her research she set up an appointment, with Saber, for an estimate.  The findings were, sagging beams and floor joists caused by weakening of members over time.  

Saber scheduled a crew to compete the work for Lisa.  The crew installed galvanized adjustable steel Smart Jacks, by digging a 24x24" foundation pit, created an engineered fill, and installed a precast foundation base, and attached and adjusted the Smart Jack.  The crew also needed to install new 4x6 wood grider beams for additional reinforcement to existing floor supports.  This was accomplished by removing the sub floor to expose the existing beams. The home was lifted to maximum practical recovery, and the sub floor was replaced.  The site was then cleaned and the project was complete. 

Homeowners in Loma Linda, California, had noticed a large crack in the slab of their foundation.  After doing some research about the methods to fix the damage caused by the soil settlement below the slab, they knew that they wanted to use a company that would inject foam under the slab.  The other options were thought to be too time consuming and expensive.  The homeowner knew they wanted something that was light weight with a quick finish time and something that would not break the budget.  The homeowners enlisted the help of Saber to repair the crack in the slab and to lift and stabilize the foundation of the home.  The crew from Saber arrived promptly at the scheduled date and time and the work was completed much to the homeowners satisfaction.  The crew injected PolyLEVEL™ beneath the foundation to stabilize the home and to perform a lift, once the lift was complete and the PolyLEVEL™ was cured, the crew then repaired the crack that had formed in the foundation using an epoxy injection.  The homeowners were very pleased with the work competed by Saber and are happy to know that their home is now stabilized and the signs of settlement are no longer an issue.

Homeowners in Chino Hills, California, had started to notice a lot of cracking in the interior and exterior of their home.  They also noticed separation that had formed in the slab of their patio deck.  These are all signs of soil settlement.  This type of settlement is due to the expansive soils beneath the homes foundation.  The homeowners knew they needed to find a fix for this issue before it became much more serious, however; they knew that they wanted to find a fix that would be best for them and not too disruptive to their lives.  The homeowners did some research and found Saber, they set an appointment for a Saber design specialist to come to the property for a free property evaluation.  The design specialist proposed that the home be stabilized and lifted to maximum practical recovery using PolyLEVEL™.  The Crew arrived and went to work using the proposed design to map out the locations in which the PolyLEVEL™ would be injected for the best results.  PolyLEVEL™ was injected beneath the foundation to fill any voids and to lift and stabilize the home.  Once the PolyLEVEL™ set up the home is now stabilized and lifted to maximum practical recovery,  The homeowners no longer see the signs of settlement that once plaqued their home.  The cracks that had formed are now closed and any doors and windows that were hard to open and close are no longer an issue.  The homeowners are happy to know that the home is also has lateral support. 

A homeowner in Desert Hot Springs, had noticed several areas around the property that the walkways had become uneven and cause concern to the homeowner due to the fact that the uneven walkways could result in a trip hazard, which could be a hassle for the homeowner in the long run.  The settlement of the slabs and walkways was mostly due to the soils located beneath the foundation, which had settled and caused voids to form in which the slabs began to sink and the walkways became compromised.   The homeowner knew it was time to find a fix for the issue, before the damage became worse.  The homeowner called Saber and set an appointment for a Design Specialist to come out and evaluate the property.  The Design Specialist proposed that the slabs and walkways be lifted and raised using PolyLEVEL™.  The homeowner was pleased with the proposal and was ready to get started on the project.  The crew from Saber was scheduled to come out and repair the foundation.  The crew began by coring penny sized holes in the slabs in the areas that would be lifted and stabilized.  The PolyLEVEL™ was then injected into the holes and the slab began to rise and level.  The whole process was rather quick and the cure time was just minutes, much less then the time it would have taken had the homeowner chosen to replace the sinking slabs. 

Homeowners in Yucaipa,  had noticed separation and cracks that had formed in the slab of their pool deck.  These are all signs of soil settlement.  This type of settlement is due to the expansive soils beneath the homes foundation.  The homeowners knew they needed to find a fix for this issue before it became much more serious, however; they knew that they wanted to find a fix that would be best for them and not too disruptive to their lives.  The homeowners did some research and found Saber, they set an appointment for a Saber design specialist to come to the property for a free property evaluation.  The design specialist proposed that the pool slabs  be stabilized and lifted to maximum practical recovery using PolyLEVEL™.  The Crew arrived and went to work using the proposed design to map out the locations in which the PolyLEVEL™ would be injected for the best results.  PolyLEVEL™ was injected beneath the slabs to fill any voids and to lift and stabilize the the pool deck.  Once the PolyLEVEL™ set up the slabs are now stabilized and lifted to maximum practical recovery,  The homeowners no longer see the signs of settlement that once plaqued their pool deck and caused tripping hazards.  The cracks that had formed are now closed and the uneven concrete was once again level.

A home in Upland, California was suffering from serious foundation settlement.  Large cracks in had formed in the slab and walls of the home and areas of the floors were sagging and walls were bowing.  The homeowner was concerned with what was going on with the home, so they began to research options on how to repair or replace the foundation.  They found that replacing the foundation all together would not only be extremely expensive, but also very time consuming, and could possibly only cover the problem, since the real issue is with the soils beneath the foundation.  The homeowner knew that wanted something for a permanent fix, but something that would not break the bank.  The homeowners researched several options and found that Saber with their many years in business and positive reviews would be the best option.  A design specialist from Saber came to the property and competed an evaluation.  The homeowner liked the proposal and set an appointment for the crew to come out and get the work started.  The crew came out to the home and prepped 5 areas where helical piers would be located, 13 areas for push piers and 4 SmartJacks to be added,  in order to repair the foundation of the home.  The holes were excavated and the piers were installed.  Once that was complete the holes were backfilled.  The crew also added SmartJacks to an area of the home that was on a crawlspace to protect the home from any future settlement.

Big Bear Lake resident Sister Rosemary contacted Saber regarding her home floor not being level. Dan Froehlich did a complete evaluation of the home.

Jake Bast, the project forman, and his crew, drilled strategic holes in the foundation, and ground out a crack between the house and the foundation. He was then able to lift and stabilize the room using our state-of-the-art PolyLevel process. Jake's team also took care of all of the additional concrete repairs at the same time.

Sister Rosemary was satisfied with the completed work and the cleanup afterward.

Crystal S contacted Saber stating that she owned a house thaat was built in 1949. She was concerned about possible future earthquake damage. Our project design specialist did a full evaluation of Crystal's home.

Using bolt plates, our crew was able to seismic retrofit this home . Crystal was satisfied with the job and the clean up.

Helendale property owners Christine and Rosemary contacted Saber regarding a commercial property that they own. The walls had exterior and interior cracks and the doors and windows were sticking in the units. There were also cracks in the garage floor. our project design specialist did a full evaluation of this building.

Our crews removed and replaced the concrete in the parking area. We added rebar to the push pier system that was installed. Last of all, we used our state-of-the-art PolyLevel process to level the uneven parts of the foundation.

Christine and Rosemary were satisfied with the changes and the clean up.

Barstow resident Gayla P. contacted Saber regarding cracks in the interior and exterior walls of her home. Our Project Design Specialist performed a thorough evaluation of Gayla's home. There were voids under the foundation, which was causing the foundation to weaken, and the walls to crack.

Our crew used Saber's PolyLevel Injection process to fill the voids under the foundation. We also used Push Piers to lift and strengthen the foundation.

Gayla was happy with the completed job, and the clean up.

Grand Terrace resident Richard L. contacted Saber regarding uneven cement edges on his swimming pool deck. The attached picture shows one of the trip hazards. Our Project Design Specialist completed a thorough inspection of Richard's home and pool area.

Our crew, used Saber's PolyLevel injection process, to raise the sinking sections of of the pool deck, thus eliminating all trip hazards.

Richard was happy with the completed Work and the clean up.

Joshua Tree resident Nikko D contacted Saber regarding cracks in the walls of her home, and sticking doors and windows. our Project Design Specialist performed a complete inspection of Nikko's home.

Our crew istalled several push piers at the base of the home's foundation. This leveled and strengthened the foundation.

Nikko was happy with the result and the clean up.

Lake Arrowhead resident James A. contacted Saber in regards to cracks in the exterior walls of his home. Our Project Design Specialist performened a thorough evaluation of James's home.

Our crew used the PolyLevel Injection Process to level the foundation and stopped more cracks from appearing.

James was happy with the results and the clean up.

Phelan resident Andrew C. contacted Saber regarding uneven slabs, creating trip hazards on their walkway. Our Project Design Specialist performed a complete home inspection.

Our crew used Saber's State-of-the-Art PolyLevel Injection Process to raise and level the sinking concrete slabs.

Andrew was happy with the result and clean up.

Running Springs resident Michael S. contacted Saber regarding trip hazards on the front porch of his home. Our project Design Specialist completed a thorough inspection of Michael's home. The concrete slabs of his front porch were sinking.

Our crew used Saber's State-of-the-Art PolyLevel Injection Processs to lift the sinking slabs and level the porch. 

Michael was satisfied with the completed job and the clean up.

Twin Peaks resident Jim C. contacted Saber regarding sticking windows and doors, and cracks in the walls of his home. Our Project Design Specialist performed a complete home inspection for Jim.

Our crew raised the home's foundation using Push Piers and all metal Smart Jacks.

Jim was happy with the job results and clean up.

Yucca Valley resident David T. contacted Saber regarding Cracks in the interior and exterior walls in his home. The concrete garage floor was also cracking. Our Project Design Specialist completed a thorough inspection of David's home. The home's foundation was sinking.

Our crew dug holes and used Push Piers to lift the foundation of David's home.

David was satisfied with the result of the job and the clean up.

Big Bear City resident Rick B. contacted Saber regarding his home's chimney shifting. Rick had already contacted a fireplace contractor to see if his fireplace could be repaired or, if the fireplace had to be replaced.

Rick's chimney foundation had a void under it. Saber filled this void by using our PolyLevel injection process. Our crew then installed Push Piers to stabilize the the chimney foundation.

Phelan resident Dave P. contacted Saber about his sinking garage floor in a metal building. Saber's Project design Specialist performed a thorough inspection on the area. The foundation had weakened from a void that formed under the slab.

Our crew filled the void using Saber's Polylevel Injection. We then installed Push Piers to Stengthen the garage floor. Dave was happy with the result and the clean up.

The picture shows a installed Push Pier.

Victorville resident James K. contacted Saber regarding trip hazards on the patio and walkway concrete slabs at his home. Saber's Project Design Specialist conducted a thorough inspection of James' home.

The earth was settling under the concrete, thus creating voids. This was also happening with the home's foundation. Saber's crew used our PolyLevel Injection Process to fill all of the voids and stop the settling issues.

James was happy with the outcome and the clean up.

The attached picture shows a Saber team member injecting PolyLevel.

Yucaipa resident Wallace contacted Saber regarding drainage issues on his property. After rains, he would have standing water in the back and on the sides of his home. Our Project Design Soecialist performed a thorough inspection. The Foundation hadn't been affected yet.

Saber's crew dug trenches and installed French Drains and and lines to connect the drains. The standing water issue was resolved. Wallace was happy with the results and the clean up.

Upland resident Melissa contacted Saber regarding Strengthening the connection between her home and Foundation. She stated that her home was built in the 1950's and that she was worried, that a Earthquake would knock her home off it's Foundation. Saber's Project Design Specialist performed a thorough inspection of Melissa's home.

Saber's crew installed Universal Foundation Plates and A35 Framing Angles to Strengthen the connection between Melissa's Home and it's Foundation. See Attached Picture. We then installed Post Caps to strengthen the connection between the home to the Support Posts.

Melissa was happy with the result of the work. Saber's work gave this California Homeowner peace of mind.

Big Bear Lake resident Tim contacted Saber regarding his vacation home. The front door of his home was jammed, and wouldn't open. He also mentioned, that the floors were creaking in his 1940's home, and waking other members his family. Saber's Project Design Specialist completes a thorough and Free Homeowner Inspection. The Floors were tilting and sagging, causing doors to jam and the floors to creak.

Saber's crew, cleared the debris from the home's Crawlspace. The attached picture shows a Boulder that Saber removed from the home's crawlspace. This was done to prepare a foundation for installation of Smart Jacks, all metal support posts. The installation of Smart Jacks and all metal Crossbeams gave the floors a contant elevation. This eliminated both issues.

Tim was very happy with the result of Saber's work.

Ontario resident Steve M. contacted Saber regarding Trip Hazard that had formed in his Pool Deck. Voids were located under the concrete slabs by Saber's Project Design Specialist.

Our Crew drilled holes through the slabs and into the voids. Then we injected Polyurethane into the voids, using Sabers State-of-the-Art PolyLevel Injection process. This raised the areas of the slabs that had sunk. Then our crew applied Nexus Plus to fill and seal the cracks. Then our crew cleaned up the area.

Steve was happy with the results. He now has peace of mind.

Apple Valley resident Jack T. contacted Saber regarding cracking in the concrete slab Foundation of his home. He had previously tried to repair this issue himself, by trying to grind the concrete. This didn't level the Foundation like he hoped. Jack told Saber that he was looking for a permanent solution to this issue. Our Project Design Specialist performed a thorough inspection, and provided a written evaluation of how to fix this issue. The soils had shifted under the slab. This had created voids. Parts of the slab were sinking, which was causing the cracking. The attached picture shows the home's foundation before we started our work.

Saber's Crew drilled holes through the slab and into the voids. Then, using Saber's State-of-the-Art PolyLevel Injection Process, we filled the voids with polyurethane. This raised the areas of the slab that had sunk. Now the entire home Foundation had a constant elevation. 

Jack was pleased with the results. Saber had solved his problem, and gave him peace of mind.

San Bernardino business Century Arrowhead Vista/SK Management contacted Saber regarding Trip Hazards created by Tree Roots, that were buckling Walkways. Sabers Project Design Specialist completed a thorough inspection. 

Saber's crew excavated and removed bucking concrete. We also cut and removed the tree roots that were causing the issue. We prepared these areas with concrete forms. Last of all our crew finished with new concrete to replace the trip hazards. The attached picture shows the completed work.

Luis M., the company representative, was happy with the completed work.

Redlands resident David B. contacted Saber regarding Trip Hazards on the concrete walkways of his home. Saber's Project Design Specialist performed a Free Homeowner inspection of David's property. Shifting soils had created voids under the walkways and patio areas.

Our Crew Lifted the areas of concrete, that were sinking into these voids. Once Constant Elevation was obtained, we filled the voids with Polyurethane, using Saber's State-of-the-Art PolyLevel Injection Process. Then Nexus Plus was applied to fill in the cracks, and give the concrete a finished look. The attached picture shows the walkway after Nexus Plus was applied.

David has peace of mind that his home is safer.

Grand Terrace resident Charles M contacted Saber regarding cracks that were appearing in the walls of his home. Saber's Project Design Specialist performed a thorough and free homeowner inspection of Charles home. Voids had formed under the foundation. This was caused by shifting soils. This had caused the foundation to sink in areas. The foundation was cracking. The support posts in the crawl space were also sliding off of their bases. The attached picture shows one of the sliding support posts.

We gave Charles the inspection report and our quote to fix these issues.

Green Valley Lake resident Chuck H contacted Saber regarding sagging floors in his home. Saber's Project Design Specialist performed a Free Homeowner inspection of Chuck's home. The Support Posts in the Crawlspace were slipping off of their bases.

Our crew attached wood girder beams to the existing Floor Joists. We then installed all metal SmartJacks with concrete bases.

Chuck was happy with the results. No more sagging floors.

Montclair resident Imara A. contacted Saber after she had her carpet removed and discovering a large crack in her concrete foundation. Saber's Project Design Specialist performed a Free Homeowner Inspection. Saber suggested that the crack be removed by cutting a channel in the foundation. Then we would pour and finish new concrete. Imara was given a copy of the inspection report and a 30 day quote.

Newberry Springs resident Desiree contacted Saber regarding cracked walkways and tree roots lifting her kitchen floor. Saber Project Design Specialist performed a Free Homeowner inspection. We recommended that the tree roots be excavated and removed. We would then excavate and remove the damaged concrete foundation. We would repour the concrete and bring the floor to a consistent elevation with the rest of desiree's home. We also recommended attaching Helical Piers to the foundation. This would lift any areas that had sunk, thus strengthening the foundation.

Desiree received a copy of out two hour inspection report and a 30 day quote.

Trona resident Merle I. contacted Saber regarding cracks in a home that he was selling. Saber's Project Design Specialist found voids causing Foundation Cracking during his inspection of the home. Saber recommended installing Helical Piers to Lift and Strengthen the Foundation. The we recommended filling the voids with Polyurethane to Stabilize the home. Merle received a written copy of Saber's Home Inspection.

Adelanto resident Jesse S. contacted Saber regarding cracking walls, and sticking doors and windows in his home. Saber's Project Design Specialist performed a thorough inspection. Voids had formed under the Foundation. The Foundation was weakening, and sinking. Saber suggested attaching Push Piers to the base of the Foundation. These Piers would strengthen the Foundation. They would also lift and give the Foundation back it's Consistent Elevation. We would also install Helical Tiebacks to stabilize Jesse's home. Last of all, we would fill the voids to stabilize the foundation.

Jesse received a written Home Inspection Report from Saber.

Mentone resident Jim J. contacted Saber regarding trip hazards on the walkways around the outside of his home. Saber's Project Design Specialist inspected Jim's home. This issue was concrete slabs that were not aligned properly, because voids had formed under them. The sunken slabs needed to be lifted. Saber's State-of-the-Art PolyLevel Injection Process is the least invasive, and most cost effective way to solve this issue. Jim received a written copy of Saber's Home Inspection Report.

San Bernardino resident Jorge G. contacted Saber regarding earthquake preparedness on his older home. Saber's Project Design Specialist performed a thorough inspection on Jorge's home. The attached picture is the Crawlspace before the Seizmic Retrofitting Components were installed.

Saber's crew attached Universal Foundation Plates, A35 Framing Angles, and Post Caps. These components combined to greatly strengthen Jorge's Home to it's Foundation.

San Bernardino resident Eileen S. contacted Saber regarding sagging floors in her home. Saber's Project Design Specialist performed a Free Homeowner Inspection. We discovered that the Wood Support Posts in Eileen's home were sliding off of their concrete bases, due to age, and years of earthquakes in Southern California.

Saber's crew reinforeced the Wood Floor Joists, with Steel I beams. Them we installed All Metal Smart Jacks with Gravel Bases.  The Smart Jacks were then Pressurized, which lifted Eileen's floor back to a consistent elevation.

Eileen is pleased with the results, and happy with the clean up, when our crew finished the job.

Real Estate Investor Kyle Z. contacted Saber regarding a Pinon Hills home. Some of the tiles were cracked in the home. Kyle wanted to make sure that this wasn't a sign of Foundation Problems. Saber's Project Design Specialist performed a full three hour inspection of this home.

There were no foundation issues. Kyle had Peace of Mind, that the home has a solid, and safe Foundation.

Yucaipa resident Nathan W. contacted Saber regarding Trip Hazards on their patio and Cracks in the Block Walls.

Saber Quoted Filling the Voids under the Patio, to Lift the sinking areas of the Patio. We also Quoted Attaching Helical Piers and Tiebacks to Strengthen and Stabilize the Wall.

Rancho Cucamonga resident Jim W. contacted Saber regarding Cracks in his Pool Deck. Please see the attached picture. The Deck was sinking into Voids. The Cracks had become Trip Hazards.

Saber's crew drilled Holes into the Voids. We used our PolyLevel Injection Process to fill these Voids with Polyurethane. This lifted the Deck back to a Consistent Elevation, and eliminated all Trip Hazards.

Chino resident Rick H. contacted Saber regarding Cracks in the Walls of his Home. Saber's Project Design Specialist performed a thorough Inspection of Rick's Home. Voids have Formed under the Foundation, which made it sink and crack.

Our crew excavated Holes, where the Foundation had sunk. We then attcahed and Pressurized Helical Piers to Lift the Foundation back to a Consistent Elevation. See attached Picture. Saber then Filled the Voids with Polyurethane.

The Cracking has stopped. The Foundation is much stronger. The Foundation has been Stabilized.

Big Bear City resident Rick B. contacted Saber regarding Cracks in the Block Wall surrounding his yard. Saber's Project Design Specialist found Voids that had formed under the walls, causing it to sink and crack.

Saber's crew installed Helical Piers, see attached Picture. This Lifted and Strengthened the Wall's Foundation. Then Helical Tiebacks were installed inside of the Block wall, and Tightened with Cables. This Stabilized the Block Wall.

Chino resident Tony C. contacted Saber regarding cracks in the walls of his home. Saber's Project Design Specialist performed a thorough Home Inspection. Voids were found under the Home's Foundation and Patio.

Saber's crew excavated Holes where the Foundation was sinking. We then attached and Pressurized Push Piers to Lift and Strengthen the Foundation. We filled the Voids with Polyurethane to Stabilize the Foundation, and to eliminate the Trip Hazard on the Patio.

The attached Picture is where a Push Pier was attached to the base of the Home's Foundation. We then Filled the Void with Polyurethane, and completed the work. This is how Saber finishes it's work.

Chino Hills resident Al D. contacted Saber regarding Door and Windows that were sticking in his Home. Cracks were also starting to form in the walls. Voids have been forming under the Foundation. The Foundation Sinking and Cracking.

Saber installed Push Piers. We Pressurized the Piers to Lift the Foundation. We then Filled the Voids with Polyurethane to Stabilize the Foundation. See attached Picture.